Ism Cummins Torque Specs

The Cummins ISM is the alternative engine to the larger ISX for local and long haul applications. Although mostly seen in daycab tractors and vocational trucks, the ISM engine can also be found in large motorhomes and fire equipment. Designed as a replacment for the original M11 engine, the Cummins ISM began with the CM570 fuel system. Contact your Cummins Filtration distributor, dealer or Cummins Filtration, Inc. If you have questions regarding the installation. Introduction This Cummins Filtration Closed Crankcase Ventilation (CCV) system is designed to remove emissions from the open crankcase system on a variety of diesel engines with blow-by flows of 12 ft3/min or less.

1. Cummins Ism Head Torque Specs
2. Torque Specs For Ism Cummins Rocker Hold Down
3. Cummins Engine Bolt Torque Specs

Cummins ISM Engines For Sale

The Cummins ISM Engines is at the forefront of the heavy-duty diesel engines in its class. The ISM undergoes thorough testing to ensure it meets the high standard Cummins demand for their products. The 6-cylinder engine produces a range of horsepower from 280 – 450. The ISM previously identified as the M11 CELECT plus but earned its ‘IS' in 1998 when it harnessed an Interact System. Each and every element of the Cummins ISM Engine is produced using the Six Sigma process that ensures a good level of quality throughout each model.

Cummins designed the M11 ISM motor with drivers in mind, therefore the ISM provides coaching and feedback of trip data to the driver to aid in efficient and comfortable driving. Adding to this, the ISM houses a Variable Geometry Turbocharger meaning a sharp throttle response and less lag that really gets your load moving.

Engine Applications and Uses

Cummins Ism Head Torque Specs

• Transit Bus
• Fire & emergency
• Heavy-Duty Truck
• Motorhome & RV
• Transit Bus

COMMON ISM ENGINE PROBLEMS & FAILURES

Itemized Below are a handful of engine problems and malfunctions commonly experienced by customers who wish to replace their either deceased or problematic ISM. Regrettably, some of the issues listed could in fact lead to the death of your M11 ISM motor, but some can be remedied if caught in time.

• Camshaft Failure
• Crankshaft Failure
• Lifter/Roller Failure
• Connecting Rod Failure
• Spun Crankshaft Bearings
• Cracked Cylinder Head(s)
• Scored Pistons and Liners
• Over Fueling
• Lack of oil or oil pressure
• Extreme Blow By
• Dropped Valves

CUMMINS ISM ENGINE REPLACEMENT OPTIONS

When it comes to the wellbeing of your engine there could be an excess of issues and mishaps - worst case scenario, you could be left with an issue where you are cornered into replacing your engine. However, some circumstances may just require you to replace some parts or components, or maybe your engine just needs a mere refreshment. Of course, cost, time, and availability will play a part in your decision making, so let us inform you of the pro's and con's of a new Cummins ISM engine from the dealer.

Remanufacturing Process

A remanufactured Cummins ISM long engine block is a great replacement for someone who has been the victim of a catastrophic internal engine failure, but luckily escaped with good re-useable external components that can be salvaged from their old motor. Long blocks are also a good alternative when trying to reduce costs in when faced with such an issue.

Our team of machinists and engine builders come to do a full core tear down, cleaning, inspection, and machining of the engine before it leaves our facility to ensure perfection each and every time.

However, it is crucial to note that all of our Cummins ISM remanufactured long blocks are constructed with a combination of both reman and new parts. However, we do not recondition or refurbish former engine parts but rather completely rebuild the old ISM motor to OEM specs.

THOROUGH CLEANING

Every Cummins M11/ISM motor is initially stripped. Blocks, heads, rods, crankshafts and camshafts are thoroughly cleaned in a chemical jet wash or hot tank to get rid of any impurities that could hasten both early component and engine failure.

Torque Specs For Ism Cummins Rocker Hold Down

CRANKSHAFTS

Prior to being thoroughly inspected by our quality control department, crankshafts are precision machined to exact tolerances, polished & magnafluxed.

CYLINDER HEADS

Cummins Engine Bolt Torque Specs

Heads are resurfaced to ensure a proper sealing surface with the block and a finish consistent with today's new gasket materials. Valve height is mic-d and every head is vacuum tested to assure an accurate valve seating.

CYLINDER BLOCKS

Blocks naturally pick up imperfections, therefore, we use magnetic particle which carefully inspects for cracks and defects. Cylinders are then bored, honed and inspected to precise tolerances. Torque plate honing is performed on some engines to prevent the chances of cylinder head distortion after the head is bolted and torqued to the block. This process stops a major cause of engine blow-by. Block surfaces are machined and then inspected to ensure proper finish.

CAMSHAFTS

Camshafts are carefully inspected and precisely machined to provide correct lift. Lobs are measured with a micrometer to make sure OEM tolerances are met.

CONNECTING RODS

Connecting rods are cleaned, then machined to O.E.M. specifications and honed to the standard diameter of original equipment for even distribution of stress on the bearings. New bushings are fitted and machined in all bushed rods. Every rod is carefully inspected for bend and twist.

NEW PARTS

Our Cummins M11/ISM long block engines receive a standard set of new parts such as pistons and rings, bearings, gaskets and seals, and liners. These new parts guarantee excellent performance and consistency throughout the lifetime of the ISM. The new parts are a combination of both OEM and Aftermarket parts when available.

Request a Quote

Please fill out the form below with your information and request. A member of our staff will be with you shortly.

REMANUFACTURED ENGINES STANDARDS

The definition of remanufacture, is to make as close to new as possible. Wearable parts are automatically replaced. All Cummins ISM engine's core material is thoroughly inspected and examined against the original equipment specifications ensuring correct dimensional tolerances. Replacement parts are new or requalified. If new, parts are made in the same production procedures as original equipment. Testing is then carried out to manufacturer specifications and original production standards.

Reman ISM Long Block Parts List:

• Intermediate Cover
• Timed Front Gear Group
• New Upper and Lower Gasket Set
• Complete Loaded Cylinder Head
• Crankshaft
• Connecting Rods
• Cylinder Block
• Camshaft
• Followers/Lifters
• Pistons
• Liners
• Rings
• **1 Year Warranty

*Note: We can provide new oil pumps, oil coolers, water pumps, turbos, injectors and fuel pumps for additional cost with the long block but will not come assembled to the engine.

**First 6 Months Parts & Labor, Second 6 Months Parts Replacement Only. Ask your sales representative for a full copy of our remanufactured long block warranty.

Give us a call today at 844-340-4114 for immediate sales and support for the Cummins 4BT, Cummins 6BT, 6CT, ISC, 855, QSB 4.5 L or CAT 3306. If you have any questions check out our FAQ Page. We are always ready to help or just listen to your crazy off-roading adventures!