What Does It Mean When A Microwave Says Se

• What Does It Mean When A Samsung Microwave Says Se
• What Does It Mean When A Microwave Says Seen

The sensor control panel is one of the weakest points of microwave ovens. At one point equipment failures occur. program selection sensor buttons stop responding to pressing or respond half the time. If one or several buttons of the Samsung microwave sticks longer than for 60 s the system will inform you with SE error code on the screen.

What Does It Mean When A Samsung Microwave Says Se

What to do if the buttons of Samsung smh8165st microwave have stuck?

Note! Many users confuse the first code letter 'S' with the number '5'. 5E and SE error codes are the same.

Get shopping advice from experts, friends and the community! My microwave/hood comb started beeping last night has a code of.SE. not sure what that is and cannot find my manuel. Microwave Specifications Power. Microwave power is measured in watts. Usually your food will cook faster and more evenly the higher the microwave wattage. You'll find microwaves available from 500 – 1,000 watts. In general, a 700-watt microwave should boil a cup of room temperature water in 2. The SE error code indicates that you have a stuck key on the control keypad or a failed electronic control board. A technician will need to diagnose and repair this type of failure. Microwaves are inherently dangerous to service. Internal high voltage components can retain a lethal electrical charge even when the microwave is completely unplugged.

If this error code appeared on the microwave screen, it is strongly prohibited to leave the microwave powered and unattended. The system can become self-activated when there is nobody at home and this may cause a fire. If you cannot power it off, always leave the microwave door open. The SE error code of the Samsung microwave cannot be reset by powering off for a while. It will appear again and again and the problem with the control panel membrane will not be fixed.

5e error and sensor panel fix

What Does It Mean When A Microwave Says Seen

You can find many fixes for the microwave sensor panel buttons over the Internet. I will tell you about one of them. But before you start repairing such equipment as a microwave yourself please note that it is under deadly high voltages (up to 5000 V even when it is off)(microwave ovens have components which absorb accumulate electricity).

Samsung microwave keypad consists of two films with lines and lands. The failure often occurs due to buttons sunken after pressing the membrane sensor which contacts the other membrane even after the slightest vibration.

Before repairing the sensor panel you need to unstick it from the microwave. After this divide it into layers. Inspect the films to make sure that their lines are in good condition. If one of them is damaged, this can be the problem. If all lines are integral, then contact closure is the problem. Perform all the following actions as carefully as possible for preventing further damage to your microwave.

1. Stick some Scotch tape or electrical tape on the inner side of the membrane along the buttons' contour (but make sure that such tape is not conductive) for increasing the area between the film and membrane and preventing unauthorized button sticking.
2. After this join the two plates and connect them to the bus.
3. Stick the sensor back.
4. Assemble the microwave in reverse order.
5. Check the button performance.

If all buttons are working when pressed only (not spontaneously) and SE error code does not appear on the Samsung microwave screen anymore, the sensor recovery operation has been completed successfully and the microwave can be used further.

This way does not guarantee a long service life of the sensor control panel as the film will be pressed further. This will lead to its failure and SE error code will appear again.

In a real sense, it can be said that such manipulations allow fixing the problem for some time (for a week or half a year). If the microwave buttons are very worn-out, it is recommended to replace the sensor.

For buying a new sensor keypad find out the number of your microwave. It is printed on the equipment tally. The sticker can be inside the microwave or on the backside. Be sure not to confuse the model and code of the Samsung microwave.

— Samsung microwave error code a1
— Samsung microwave error code E-11
— Samsung microwave error code E-13
— Samsung microwave se or 5e error
— Samsung microwave error code e83
— Samsung microwave error code SE
— Other error codes

Samsung microwave error code a1

There is either a switch or motor damper problem. Check the damper switch. If it is ok, have the damper motor replaced (2 screws).

Samsung microwave error code E-11

This error code denotes a humidity sensor issue. You can see the sensor in above your oven on the left. Also, there is the part number and a link to the part, which you may need to order and install if it comes to replacing the faulty one. Unscrew the top the top vent panel above the oven door and remove it. The microwave is designed in such a way that the sensor cannot be removed separately, so the entire panel has to be removed. The sensor itself costs $25.

Samsung microwave e-13

The E-13 T1 Max time error appears when the unit fails to preheat properly. There are quite a number of possible causes: low voltage, a faulty damper seal, thermistor or control circuit board. Check each of these parts and replace it if necessary.

Samsung microwave se or 5e error

The SE error code iss often mistakenly referred to as 5E. It occurs when a key on the keypad is pressed continuously or shorted. It is very dangerous, because your microwave may start running on its own and cause fire. If you ssee this code on your microwave's display, unplug it right away and do not plug it baack in until you fix the problem. Also, to prevent it from running, you can leave its door open.

In some cases, the error may occur if the keypad strip is greased, dirty or moist. However, for the most part, it happens because of shorting and requires replacement. Please, do not be in a hurry to follow the numerous ‘video tips' and ‘instructions' advising methods like ‘paper inserts' and similar stuff.

Samsung provides a service bulletin, which describes the only effective and correct solution and specifies models, to which these steps can be applied if they show this error code, intermittently or constantly. Please, do not use any other methods not relating to the bulletin.

Where do I find the model code and the model number?

The model number is printed on a tag inside the cooking chamber. It should be noted that a model number is not the ssame as a model code. The latter is found on the keypad's connector, and you need to remove the entire control panel to read it.

Samsung microwave error code e83

This error code reports an issue in one of the three door switches. If you see it on the display board, check each switch using a multimeter. If there is a faulty one, repair or replace it. If all three are ok, check the display control board: most likely, it is not reading the switches properly. Take steps to repair or replace the display control board.

Samsung microwave se error

If there is SE flashing on your microwave's display, there is a sensor error. Most likely, the humidity sensor has shorted. You need to disassemble the device and check the sensor directly. The element may be located near one of the vents on the microwave's cavity. In most cases, shorted humidity sensors have to be replaced.

Fixing it

Undo the two screws of the top vent, then one above the keypad. Take off the vent and the key pad VERY CAREFULLY. Disconnect wire harnesses. Try to remember each connection or picture them using a phone cam. Check all elements for moisture, which could have caused the short-circuit. Dry the system with condensed air. If necessary, leave it to sit open for several hours. Put your oven back together and test it. If the error is still there, address a professional technician.

Other error codes

The table shows the error codes for microwave ovens. These are the most common malfunctions. Check the error code on the display with the information in the table. Read about a possible solution to this problem. Some faults require that you call the service center.